MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM :)
Microphone Channel
A balanced MIC input through a combined XLR/jack input connector (15). Level, Bass &Treble controls in front panel. GAIN adjust (16) and INSERT jack 1/4" connection (17) for external effects only in MIC input, in back panel. The INSERT connection could be used also as LINE input.
Master Out 1 & 2 and REC output
Two completely independent high-powered main program outputs. OUT 1 (0dBV), controlled through Master 1 (19a), is electronically balanced and with XLR3 (19b) connectors. OUT 2, adjusted at a nominal +6dB level, is controlled through Master 2 (20a), is non-balanced and with RCA-cinch (20b) connectors for monitoring or session output, and finally a recording REC (21) output with RCA.
New Monitoring system
For a very complete sound mastering, the new HAK 360 allows the performer to monitor both PGM (Master signal) and/or PFL (Pre-fader signal) through the VU-METER (7) as well as the powerful Headphone system (8). For pre-fader listening, a MONITOR-MIX crossfader is active when the Pgm/Pfl switch selector is in PFL position; then direct crossfading between PFL input 1 and PFL input 2 is possible. On PGM position the mixer can be fully performed through the Headphones. A 0dB LED (9) nearby the MASTER 1 level knob allows to easily control the Output level.
Session Input
The HAK 320 features a SESSION Input that allows the DJ to organize a Mixing Session with others in a daisy chain formation. The SESSION potentiometer allows adjusting the level of the foregoing DJ connected to the HAK 360.
Powerful 3 band EQ
The HAK 320 features a High/Mid/Low Band EQ that allows the Dj to boost tones up to +10 dB and CUT them down to -25/-30 dB! The EQ is horizontally displayed for an easier and faster manipulation.
Effect Send Switches
The switches allows the Dj to send the PGM1 or/and PGM2 post fader stereo signal to effect external devices through the EFF output. The already processed signal is returned to the main bus through the MIX input.
Balance Slider
One Balance short slider per channel allows the Dj to execute "Stereo-Pan-Scratches" in a fast and easy fading manipulation.
New Cut switches
The HAK 360 features brand new "fat designed" CUT switches, extremely smooth and durable. The switches are multidirectional, offering 8 adjustments accessible by removing the front panel.
Crossfader
New ECLERPROFader with Slope adjustment and Reverse switch
Please refer to HAK 310 ECLERPROFader description [+].
The curves of the Faders are adjustable through a potentiometer with a very wide range of curves from the fastest scratch to the smoothest contour. A HAMSTER switch allows reversing the crossfade and fading function; when activated, three red led displays the Normal/Reverse position of the Fader 1, Fader 2 and/or also the Crossfader
The ECLER ETERNAL Crossfader is an inductive fade technology based on a magnetic control. An extremely light aluminium screen (0,5 gr.) cuts the flux lines of a magnetic field created between two sets of coils.
In addition to the standard REVERSE and full SHAPE adjustment, the ETERNAL Inductive Fade system allowed ECLER to integrate unique "Tuning" features that will give the HAK360 the most accurate "battle" set-up:
CROSSMODE selector
The FADE Mode will give the crossfader a progressive "roll-off" curve meanwhile the SWITCH Mode will "square" the crossfader curve in order to perform almost as a Switch for fast "scratches".
SHAPE Adjustment
A knob SHAPE at the housing front lets you finely adjust the crossfader slope from soft to hard.
REVERSE Switch
So-called "Hamster Switch", which reverses the crossfader normal direction.
Electronic CUT-IN-TIME correction
Allows you to finely adjust the distance (from 0mm to 3mm) between the extreme end of the crossfader and the very first "fade-in" point. The shortest position will give you almost an instant “Cut-in-time”; to find the shortest “Cut-in-time”, the crossfader must be locked on the very end of the potentiometer in fade- out position (the PGM is fully attenuated) and the CUT-IN-TIME knob must be turned to the right until (just before) you get the sound. To lengthen the crossfader “Cut-in-time”, turn the knob to the left.